Adding Control with a Total Station in Siteworks
Sitech Northeast
29 steps
2 minutes
Before you begin, ensure your robot is set up over the already establish control on site and that everything is within tolerance and checking in.
1
Begin by tapping on your antenna/target height. You will need to confirm a few settings.
2
Confirm you have the appropriate target selected. Tap on target type.
3
If using the target that we shipped with your robot, you will want to select MultiTrack target from the dropdown menu.
4
Set your track type to Active mode.
5
On the bottom of your MultiTrack target, you will see a dial. This is your target ID, match your target ID in Siteworks to what it is set on the prism. Tap accept when finished.
6
Tap okay.
7
Confirm your target height is accurate to your setup then tap ACCEPT.
If only using the MultiTrack target skip to step 14.
8
If you are not using a MultiTrack target, tap on your Target/Antenna height again to change your target type.
9
Select target type.
10
Select the appropriate target you are using. If you are using a target that is not listed select the custom option. (i.e. wall mount prisms).
11
Enter a target name.
12
Enter the prism constant. Should be included in prisms specs. Tap accept when done.
13
Confirm the target height and Tap accept.
14
Tap on the top left menu.
15
Select measure new control point.
16
Select new control points.
17
Navigate to where you would like to shoot a new control point with your rod or align your gun with a prism. Tap on the blue plus button to record the point.
18
Give your new control point a name and code. Tap accept.
19
A new triangle should appear in your plan view showing that you have recorded a new control point. If you want to record an additional point, simply navigate to the next spot on site and tap the blue plus button again.
20
Confirm the name and code and tap accept.
21
Tap the settings wheel in the plan view.
22
Check Point Names.
23
Check Point codes.
24
Tap accept.
25
You should now see your point name and codes displayed in the plan view. Tap the top left menu.
26
Tap data management.
27
Tap point manager.
28
Tap enter/edit control points.
29
You will see a list of your control points with their respective data.
Adding Control with a Total Station in Siteworks
Sitech Northeast
29 steps
2 minutes
Before you begin, ensure your robot is set up over the already establish control on site and that everything is within tolerance and checking in.
1
Begin by tapping on your antenna/target height. You will need to confirm a few settings.
2
Confirm you have the appropriate target selected. Tap on target type.
3
If using the target that we shipped with your robot, you will want to select MultiTrack target from the dropdown menu.
4
Set your track type to Active mode.
5
On the bottom of your MultiTrack target, you will see a dial. This is your target ID, match your target ID in Siteworks to what it is set on the prism. Tap accept when finished.
6
Tap okay.
7
Confirm your target height is accurate to your setup then tap ACCEPT.
If only using the MultiTrack target skip to step 14.
8
If you are not using a MultiTrack target, tap on your Target/Antenna height again to change your target type.
9
Select target type.
10
Select the appropriate target you are using. If you are using a target that is not listed select the custom option. (i.e. wall mount prisms).
11
Enter a target name.
12
Enter the prism constant. Should be included in prisms specs. Tap accept when done.
13
Confirm the target height and Tap accept.
14
Tap on the top left menu.
15
Select measure new control point.
16
Select new control points.
17
Navigate to where you would like to shoot a new control point with your rod or align your gun with a prism. Tap on the blue plus button to record the point.
18
Give your new control point a name and code. Tap accept.
19
A new triangle should appear in your plan view showing that you have recorded a new control point. If you want to record an additional point, simply navigate to the next spot on site and tap the blue plus button again.
20
Confirm the name and code and tap accept.
21
Tap the settings wheel in the plan view.
22
Check Point Names.
23
Check Point codes.
24
Tap accept.
25
You should now see your point name and codes displayed in the plan view. Tap the top left menu.
26
Tap data management.
27
Tap point manager.
28
Tap enter/edit control points.
29
You will see a list of your control points with their respective data.
