How to add a bull nose cutout for a shower bench
This guide provides instructions for adding a bull nose cutout to a shower panel.
14 steps
Obe
Smartglazier
Add a corner notch
1
From the "**Design"** screen: - **Right-click** on a panel to add a corner notch - Select **"Layout"**
2
Click on **"Set Notches"** Select a **Location** for the notch (i.e. Bottom Right)
3
Select how many steps you require on the notch - i.e. single, double or triple.
4
Enter your dimensions accordingly. **Hint:** You can do this via the **Measurement Grid** tab, or click on a letter on the diagram to enter the dimension for that edge.
Add a rectangular notch cutout
5
Click **"Features"**
6
Click **"Cutouts"**
7
Click **"Custom"** and search for **"Rectangular Notch"**
8
**Drag and drop** the cutout to the correct edge of the **"3D View"** diagram.
9
OR **double click** the cutout and manually select the **"Panel"** and **''Edge''** Tip: The Edge would typically be **"<Left/Right> Notch Vertical"**.
10
- Select **"Top"** in the **"From end of glass edge"** field - Enter the **''Offset to cutout centre"** ***Hint:*** *Since cutout offsets are measured to the cutout centre, and the cutout is placed on the top of the corner notch vertical edge, you can calculate the offset by dividing the height of your required rectangular notch by two.*
11
Enter a value into the **"Notch Inwards"** field - this should be the width of the notch, or how far in from the edge it goes.
12
Enter a value in the **"Notch Along"** field - this should be the height of the notch, or how long along the edge it goes.
13
Click **"Add Cutout"**, then **"Dismiss"** to close the pop-up.
14
The diagram will now show the rectangular cutout on the corner notch.
How to add a bull nose cutout for a shower bench
This guide provides instructions for adding a bull nose cutout to a shower panel.
14 steps
Obe
Smartglazier
Add a corner notch
1
From the "**Design"** screen: - **Right-click** on a panel to add a corner notch - Select **"Layout"**
2
Click on **"Set Notches"** Select a **Location** for the notch (i.e. Bottom Right)
3
Select how many steps you require on the notch - i.e. single, double or triple.
4
Enter your dimensions accordingly. **Hint:** You can do this via the **Measurement Grid** tab, or click on a letter on the diagram to enter the dimension for that edge.
Add a rectangular notch cutout
5
Click **"Features"**
6
Click **"Cutouts"**
7
Click **"Custom"** and search for **"Rectangular Notch"**
8
**Drag and drop** the cutout to the correct edge of the **"3D View"** diagram.
9
OR **double click** the cutout and manually select the **"Panel"** and **''Edge''** Tip: The Edge would typically be **"<Left/Right> Notch Vertical"**.
10
- Select **"Top"** in the **"From end of glass edge"** field - Enter the **''Offset to cutout centre"** ***Hint:*** *Since cutout offsets are measured to the cutout centre, and the cutout is placed on the top of the corner notch vertical edge, you can calculate the offset by dividing the height of your required rectangular notch by two.*
11
Enter a value into the **"Notch Inwards"** field - this should be the width of the notch, or how far in from the edge it goes.
12
Enter a value in the **"Notch Along"** field - this should be the height of the notch, or how long along the edge it goes.
13
Click **"Add Cutout"**, then **"Dismiss"** to close the pop-up.
14
The diagram will now show the rectangular cutout on the corner notch.
