Create/Delete an Avoidance Zone in Siteworks 1.81+
Sitech Northeast
19 steps
59 seconds
Creating an Avoidance Zone
To create an Avoidance Zone, a closed boundary line must be shot with your rover that contains the area to be avoided.
1
In the plan view of Siteworks tap on the Measure Type button. Or go to the top left menu. then measure type.
2
Tap on New Line in the upper right corner.
3
Give your Avoidance Zone line a name.
4
In the Line Type drop down menu, select Avoidance Zone.
5
Tap Accept.
6
To begin shooting your Avoidance Zone line, tap on the blue plus button in the lower right corner or click enter on your keyboard. Every time the blue plus button is tapped, a new line point will be created.
7
Continue to make your boundary line by tapping the blue plus button.
8
Continue to make your boundary line by tapping the blue plus button.
When shooting your Avoidance Zone line, do not cross your start point with you end point. Make sure to stop short of your start point.
9
Once you have shot the last point of your line, tap the complete line button in Siteworks.
10
Tap Yes to save the Avoidance Zone.
11
A red area will now appear in the Siteworks plan view which represents the Avoidance Zone.
12
If the instrument operator walks into the Avoidance Zone an alert will pop up on Siteworks and prevent you from using any Siteworks functions until you leave that Avoidance Zone with the rover.
When created, Avoidance Zones will be applied throughout the entire project. I.E. the Avoidance Zone will be visible for all Work Orders and Designs in the Project.
13
Notice the line is highlighted red when inside the avoidance zone.
14
Outside of the Avoidance Zone for comparison.
Deleting an Avoidance Zone
If you are attempting to delete an Avoidance Zone from a project and you're a running a Siteworks version previous to 1.81, you must delete the Avoidance Zone .dxf file from the SCS900 Data project folder in the Windows File Explorer.
15
To delete an Avoidance Zone perform a long tap and hold over the Avoidance Zone line.
16
Tap Delete Line.
17
Tap Yes.
18
Tap "Yes".
19
Tap Yes. The avoidance zone should now be deleted.
Create/Delete an Avoidance Zone in Siteworks 1.81+
Sitech Northeast
19 steps
59 seconds
Creating an Avoidance Zone
To create an Avoidance Zone, a closed boundary line must be shot with your rover that contains the area to be avoided.
1
In the plan view of Siteworks tap on the Measure Type button. Or go to the top left menu. then measure type.
2
Tap on New Line in the upper right corner.
3
Give your Avoidance Zone line a name.
4
In the Line Type drop down menu, select Avoidance Zone.
5
Tap Accept.
6
To begin shooting your Avoidance Zone line, tap on the blue plus button in the lower right corner or click enter on your keyboard. Every time the blue plus button is tapped, a new line point will be created.
7
Continue to make your boundary line by tapping the blue plus button.
8
Continue to make your boundary line by tapping the blue plus button.
When shooting your Avoidance Zone line, do not cross your start point with you end point. Make sure to stop short of your start point.
9
Once you have shot the last point of your line, tap the complete line button in Siteworks.
10
Tap Yes to save the Avoidance Zone.
11
A red area will now appear in the Siteworks plan view which represents the Avoidance Zone.
12
If the instrument operator walks into the Avoidance Zone an alert will pop up on Siteworks and prevent you from using any Siteworks functions until you leave that Avoidance Zone with the rover.
When created, Avoidance Zones will be applied throughout the entire project. I.E. the Avoidance Zone will be visible for all Work Orders and Designs in the Project.
13
Notice the line is highlighted red when inside the avoidance zone.
14
Outside of the Avoidance Zone for comparison.
Deleting an Avoidance Zone
If you are attempting to delete an Avoidance Zone from a project and you're a running a Siteworks version previous to 1.81, you must delete the Avoidance Zone .dxf file from the SCS900 Data project folder in the Windows File Explorer.
15
To delete an Avoidance Zone perform a long tap and hold over the Avoidance Zone line.
16
Tap Delete Line.
17
Tap Yes.
18
Tap "Yes".
19
Tap Yes. The avoidance zone should now be deleted.
